Cromer Roofers provides commercial roofing across Aylsham - from early warning signs and planned maintenance through to full roof replacement on retail units, industrial buildings, farm buildings and holiday accommodation.
Call any time. Calls are answered day and night and passed straight to our roofers.
A commercial roof is a working asset. When it starts to fail, it rarely gives you much warning - and when it does give warning signs, those signs are often misread or ignored until water is getting in and the damage bill is far larger than the repair bill would have been. We work on commercial properties across Aylsham and the surrounding North Norfolk area, covering everything from flat roof replacement and box gutter relining to roof light installation and emergency patch repairs.
Commercial roofs face harder conditions than domestic ones. Larger flat areas pond water. Box gutters and parapet gutters fill with debris. Roof lights crack and their seals fail. Plant equipment, engineers and delivery staff walk on surfaces that were never built for regular foot traffic. All of this accelerates wear at a rate most building owners do not expect.
Most commercial roof failures do not happen suddenly. They build up over months or years, and there is almost always a point at which a well-timed repair would have prevented a full replacement. Knowing what to look for - and what it means - can save a significant amount of money.
This is the sign most building owners notice first, but by the time water is tracking through to a ceiling or an internal wall, the entry point on the roof may already be well established. Water travels horizontally across flat membranes, along joists and through insulation before it appears internally, so the wet patch you can see is rarely directly below the source of the leak. A proper roof inspection traces the water back to its origin rather than just treating the symptom.
On a felt flat roof, blistering is caused by moisture becoming trapped between layers of the felt or between the felt and the deck below. When the roof heats up in warm weather, the moisture turns to vapour and forces the layers apart. Small blisters are a maintenance issue. Large blisters that have burst, or areas of widespread blistering across a large section of the roof, often indicate that the membrane as a whole has lost its integrity and is no longer doing its job.
Flat roofs are designed with a fall, usually a minimum of 1:80, to direct water towards outlets. If water is ponding for more than 48 hours after rain, it means either the falls have been lost - often because the roof deck has deflected or sagged - or the outlets are blocked. Persistent ponding accelerates the breakdown of felt and EPDM membranes and significantly increases the load on the roof structure beneath.
Where the flat roof surface meets a wall, a parapet, a roof light frame or any other upstand, the detailing is almost always the first area to fail. Thermal movement, frost and UV exposure cause lead, mortar and sealant to crack and open over time. These are relatively small repairs when caught early. Left unchecked, they allow sustained water ingress behind the upstand and into the wall construction, which is a far more serious and expensive problem to fix.
Box gutters run internally within the roof structure on many commercial and agricultural buildings. They are prone to blockage from moss, debris and compacted organic matter, and because they are not always visible from ground level they can overflow for extended periods without anyone noticing. A blocked box gutter that overflows into the building is one of the most common causes of serious internal water damage in commercial properties. Lining a deteriorated box gutter with EPDM or a torch-on felt system, and fitting an overflow outlet, is the correct long-term fix.
On agricultural buildings and older industrial units with profile sheet roofing, gaps and corrosion holes in the sheeting are a direct route for water, birds and vermin. Isolated sheets can usually be replaced. Widespread corrosion across a large area of a steel or fibre cement roof normally means the whole covering needs replacing rather than patching.
Moss on a commercial pitched roof retains moisture against the surface below it, accelerating the breakdown of mortar at ridge and hip junctions, lifting slates and tiles at the edges, and blocking valley gutters. Algae and lichen are slower-acting but also trap moisture. Biocide treatment and clearance is a maintenance measure. It does not repair the underlying damage already done to pointing, flashings or tiles.
Age is a factor, but it is rarely the only one. The following causes often lead to early failures on commercial roofs.
A flat roof replacement on a commercial building typically starts with stripping the existing covering back to the deck. The deck is inspected for rot, deflection or structural movement. Damaged sections of deck are replaced before any new covering goes on - this is a step that should never be skipped, because a new membrane laid over a failing deck will fail early.
The most common systems used on commercial flat roofs are torch-on (hot-applied) felt and EPDM rubber membrane. Torch-on felt is a multi-layer built-up system that bonds fully to the deck and provides a durable, tested surface when correctly installed. EPDM is a single-ply rubber membrane that is cold-applied, highly flexible and well-suited to roofs with complex detailing around outlets and upstands. Both are established systems with long track records in the UK.
Typical commercial flat roof replacement costs in Norfolk range from around £70 to £120 per square metre depending on access, deck condition, detailing complexity and the system specified. A 200-square-metre industrial unit roof might therefore cost between £14,000 and £24,000 fully installed, including deck repair and new drainage detailing. These are general indicative figures - an accurate price requires a survey.
Pitched roofs on commercial buildings are commonly finished in slate, clay tile or fibre cement profile sheet. Re-roofing in natural slate provides a long-lasting covering that suits the character of older agricultural and residential-commercial properties. Concrete and fibre cement alternatives are more cost-effective where appearance is less of a priority.
A re-roof on a commercial pitched building involves stripping the existing covering, inspecting and replacing any damaged timber in the roof structure, installing a modern breathable underlay, and fixing new battens before the new tile or slate covering is laid. Ridge and hip bedding is replaced with modern dry-fix systems where appropriate, which eliminates the cracking and displacement that mortar bedding is prone to over time.
A commercial roof survey before purchasing a building, renewing a lease, or planning a renovation is a sound investment. A proper inspection covers the membrane or covering condition, drainage outlets and box gutters, all flashings and upstand details, roof lights, and the visible structure beneath where access allows. It gives you an honest picture of remaining life and what maintenance or replacement work is needed in the short, medium and long term.
If you have noticed any of the warning signs described above on a commercial property in Aylsham or nearby, call us to arrange a roof survey. We will tell you plainly what we find and what the options are.
If you manage a commercial property in Aylsham and you are concerned about your roof - whether that is a visible leak, a long-deferred inspection, or a purchase you want to check before committing - call Cromer Roofers directly. We will arrange a survey and give you a clear, honest assessment of what the roof needs.
No obligation · We'll call you to arrange a free visit
Call any time. Calls are answered day and night and passed straight to our roofers.