Urgent leak or storm damage? Call 01263 808938 - answered day and nightUrgent leak? Call 01263 808938
Cromer Roofing Specialists
01263 808938 Get a Quote →

Exterior Cladding in Aylsham

If your cladding is showing signs of rot, damp, or cracking, Cromer Roofers can strip it back and fit a lasting replacement for your Aylsham home.

Urgent leak or storm damage?

Call any time. Calls are answered day and night and passed straight to our roofers.

Call now: 01263 808938
Exterior Cladding · Aylsham

Expert Exterior Cladding
in Aylsham

What exterior cladding does and why it matters

Exterior cladding sits over your building's outer walls and takes the full force of the weather so the structure beneath does not have to. A well-fitted system keeps wind-driven rain out of the wall build-up, reduces heat loss through exposed masonry, and gives the elevation a clean, finished appearance. When cladding fails, the consequences go well beyond cosmetics - damp gets into the wall, timber frames rot, and insulation breaks down.

We install timber, composite, and fibre cement cladding on houses and commercial premises. Each material has different strengths, and choosing the right one depends on what your walls are built from, how exposed the elevation is, and what maintenance you are prepared to do over the years ahead.

Warning signs your cladding needs attention

Most cladding problems do not announce themselves all at once. They build slowly, and by the time they become obvious from the pavement, the damage behind the boards is often further along than the visible surface suggests. Knowing what to look for early saves a straightforward replacement job from becoming a structural repair.

Softness, rot, and fungal staining on timber boards

Timber cladding that has not been maintained properly is the most common source of failure. Run your hand along the boards and press gently at the joints and lower edges - if the wood feels spongy or gives under light pressure, moisture has been sitting in the grain for some time. Dark streaking, green algae, and black fungal patches are earlier indicators that the surface coating has broken down and water is no longer running off cleanly.

The bottom courses and anywhere close to a flat roof, a parapet, or a poorly detailed sill are the highest-risk spots. Water pools or runs back against the boards at these points, and if the gap between the bottom of the cladding and any horizontal surface below it is too small, capillary action draws moisture up into the timber. This is a detailing problem as much as a materials problem, and it is one reason why a replacement job done properly involves checking and improving those junctions, not just swapping boards.

Cracking, warping, and gaps between boards

Fibre cement and composite boards can crack if they were installed without adequate expansion gaps or if fixings were over-driven. A board that has been pinned too tight cannot move with temperature changes, and over a few seasons the stress splits the board or lifts the fixing point. Warping is a sign of moisture getting behind the boards - often because a joint was left unsealed or a horizontal ledge above is directing water onto the face of the cladding rather than throwing it clear.

Gaps that open up between boards are worth taking seriously even if the boards themselves look sound. A gap of a few millimetres is enough for driven rain to get behind the cladding and sit against the breather membrane or, worse, against bare masonry if the membrane was not installed or has failed. In an exposed position, even a small defect in the weathering line lets in a surprising volume of water over a wet season.

Damp patches on internal walls

If you are seeing damp on an internal wall that sits behind cladded elevation, the cladding system is the first thing to investigate - but it is not always the only culprit. A failed cavity tray, a cracked render patch that was supposed to be protected by the cladding, or a missing or damaged breather membrane can all contribute. A proper diagnosis means looking at the whole wall build-up, not just the outer face.

Cold spots and condensation on the inside of an external wall can also point to a failure in the insulation layer behind the cladding. Some older rainscreen installations used insulation boards that were not adequately fixed to the wall, and over time they slip or compress, leaving gaps in the thermal layer. The heating bill goes up before the damp patch appears.

Failing fixings and loose sections

Cladding that moves or rattles in the wind is a fixing problem. Either the original fixings were undersized, the substrate they went into has degraded, or the fix pattern was too wide. A section of cladding that lifts in a gust can strip back further sections with it and expose a large area of wall very quickly. Any movement should be investigated promptly rather than left until the next maintenance round.

Stainless steel fixings are standard on any coastal or semi-rural installation because standard steel corrodes and the rust staining works its way through the boards. If you see orange streaking running down from fixing points, the original fixings were not specified correctly for the exposure - and they will eventually fail completely.

What causes cladding to fail prematurely

Poor installation is behind most early failures. Cladding systems rely on a sequence of details - back-ventilated cavities, correctly lapped breather membranes, sealed penetrations, properly designed junctions at windows and sills, and fixings into a sound substrate. If any one of those is missed, the system underperforms even if the boards themselves are good quality.

Under-specified materials for the exposure level is the next most common cause. A smooth-faced engineered timber board suitable for a sheltered urban location will not perform the same way on an elevation that catches rain-bearing wind. Composite and fibre cement boards generally handle exposure better with less maintenance, which is why they are often the more practical choice for properties outside town centres.

Lack of maintenance over time also plays a part. Timber cladding in particular needs periodic recoating - the interval depends on the product, but leaving it significantly beyond the manufacturer's recommended cycle allows the surface to open up and moisture to enter the grain. Once that happens, no amount of surface treatment will reverse it and replacement becomes the only option.

Choosing the right replacement cladding

Timber remains a popular choice for its appearance and the fact that it can be painted or stained to match existing details. It requires more maintenance than other materials, but properly specified and coated timber with correct back-ventilation performs well for many years. Modified and engineered timber options have better dimensional stability than standard softwood and resist moisture more effectively.

Composite cladding boards - typically a mix of wood fibre and polymer - offer a timber appearance with lower maintenance requirements. They do not need periodic recoating and are resistant to rot and insect damage. The range of profiles and colours has improved considerably, and they suit both traditional and contemporary elevations.

Fibre cement cladding is highly durable, takes paint well, and handles exposure without warping or rotting. It is heavier than timber or composite and requires fixing into a sound substrate, but once installed it is one of the most low-maintenance options available. It is a common choice where the priority is longevity over the warmth of a natural timber appearance.

What a replacement job involves

We strip the existing cladding back fully and assess the substrate, breather membrane, and any insulation layer before any new material goes on. If the membrane is torn, bridged, or missing, it is replaced. If the battens or counter-battens are damaged, they come out too. Cutting corners at this stage is where problems recur.

New boards are fixed to a ventilated batten system so air can circulate behind the cladding and any incidental moisture can drain away rather than sit against the wall. Junctions at windows, sills, eaves, and any penetrations are detailed carefully because these are where water finds its way in when the work is done in a hurry.

Exterior cladding replacement on a typical semi-detached house elevation in the Aylsham area runs from roughly £80 to £150 per square metre installed, depending on the material chosen and the condition of what is beneath. A full survey of the existing substrate is needed before any accurate figure can be given.

Talk to us about your cladding

If you have noticed any of the signs described above - soft or discoloured boards, gaps, damp patches inside, or anything that moves or rattles - call Cromer Roofers for a roof and cladding survey. We work across Aylsham and the surrounding North Norfolk area and can give you a clear picture of what needs doing before you commit to any work.

Why choose Cromer Roofers?

  • Free survey and itemised quote
  • Fixed price - no surprises
  • Local team

Get your free quote

No obligation · We'll call you to arrange a free visit

By submitting you agree to being contacted about your enquiry. No spam, ever.

Urgent leak or storm damage?

Call any time. Calls are answered day and night and passed straight to our roofers.

Call now: 01263 808938