Rotten fascias, blocked gutters, and crumbling soffits can all lead to water damage on homes - and most of the warning signs are visible from the ground.
Call any time. Calls are answered day and night and passed straight to our roofers.
Fascias are the horizontal boards fixed to the ends of your roof rafters, just behind the gutters. Soffits close the gap between the fascia and the wall beneath the eaves. Together they protect the roof structure from rain and wind, and they carry the weight of your guttering. When either board fails, water finds its way into the roof void and down the cavity wall.
We replace and repair UPVC and timber fascias, soffits, and guttering on homes across Aylsham and the surrounding villages. Every job includes properly aligned gutter falls so water drains away cleanly rather than sitting and overflowing. Boards are colour-matched so the finished result looks deliberate rather than patched.
Most homeowners notice something is wrong long before they understand what is causing it. The following signs are worth acting on quickly, because the underlying damage tends to spread faster than people expect.
Painted timber fascias absorb moisture over years of exposure to rain and frost. When the paint starts to peel or bubble rather than simply chalk, it usually means water has already penetrated the wood beneath. At that stage, repainting will not hold for long. The board is softening from behind and will eventually pull away from the rafter feet, taking the gutter bracket fixings with it. Replacing the board at this point costs less than dealing with the rot, the damp, and the gutter failure together later.
A gutter that is visibly separating from the board above it - leaning forward or dropping at one end - is a sign that the fascia itself has weakened. The screws or brackets that fix the gutter back into the board are only as secure as the material they are fixed into. Rotten timber compresses and splits under load, so the bracket pulls free. This is not a gutter problem; it is a fascia problem that is presenting through the gutter.
If a damp patch appears at the edge of a ceiling rather than in the middle, and there is no obvious roof tile damage, the source is often a failed soffit or fascia joint rather than a slipped slate. Water tracks along the top of the soffit board and drips into the roof void at the lowest point, which sits directly above the edge of your top-floor ceiling. A quick look from outside at the soffit boarding - any sagging, dark staining, or visible gaps - will usually confirm it.
Soffit boards sit in a sheltered spot under the eaves, but they still get wet from wind-driven rain and from condensation inside the roof void when ventilation is poor. Timber soffits that have darkened unevenly, or that show patchy mould growth, are holding moisture. In mild cases the board can be treated and repainted; in most cases where the staining has been present for more than one winter, the timber has softened enough that replacement is the more lasting option.
A gutter that drips or runs over the front edge during or after rain - even when it is not blocked with leaves - has either a failed joint, a section that has lost its fall, or a downpipe connection that is partially blocked lower down. Water should flow steadily towards the downpipe outlet, not pool and overflow. Sagging in the gutter run is usually caused by a bracket that has worked loose from a failing fascia board behind it.
UPVC expands and contracts with temperature changes. On a correctly installed run, small expansion gaps are left at each joint to allow for this movement. If UPVC fascia or soffit boards were installed without adequate expansion allowance, or if the original installation used standard trim that has since degraded, the joints can split open over time. Open joints let in water and allow insects and birds to enter the roof void. A split UPVC board can sometimes be repaired with a proper joining sleeve; a board that has cracked along its length needs replacing.
The fascia, soffit, and gutter system works as a unit. A blocked or overflowing gutter saturates the fascia board behind it every time it rains. A rotten fascia allows water to reach the top of the wall plate - the horizontal timber that carries your roof rafters. Once the wall plate is damp, it becomes vulnerable to wet rot, which weakens the structural base of the roof. None of this is visible from inside the house until the damage is significant.
On older properties where the original installation was timber, it is common to find that the soffit has failed first because it faces downward and traps moisture. The fascia looks sound from the front but is already soft at the back where it meets the rafter ends. Probing the board with a screwdriver before assuming it is solid is a sensible precaution during any survey.
UPVC boards are the standard choice on most homes today. They do not rot, they require no painting, and they are available in a wide range of colours and woodgrain finishes. A correctly installed UPVC system will typically outlast a painted timber installation by a significant margin with virtually no maintenance beyond an occasional clean.
Timber remains the correct material where planning restrictions apply - on listed buildings or in designated conservation areas - or where a homeowner specifically wants the painted finish and is prepared to maintain it. The key difference is that timber needs repainting every few years to remain protected; UPVC does not.
If you are unsure whether your property has any planning constraints, the local planning authority can confirm this before any work starts. It is worth checking before ordering materials.
A well-done fascia, soffit, and gutter replacement involves more than swapping boards. The rafter feet should be checked for any soft spots before the new fascia is fixed. Any existing roofing felt that overhangs into the gutter should be trimmed or redirected with a drip strip so water sheds cleanly. Ventilation of the roof void - either through vented soffit board or separate vent inserts - should be maintained or improved, not blocked off by the new boards.
Gutter falls matter. A run that sits perfectly level will hold water and eventually leak at every joint. The correct fall for a standard half-round or square-profile gutter is typically around 1:600 - roughly 3mm drop for every 1.8 metres of run. On long runs, the gutter should be set on a chalk line before brackets are fixed, not adjusted by eye.
Downpipes should be checked at the same time. A new gutter connected to a partially blocked or cracked downpipe will simply move the overflow problem to a different location.
Costs depend on the size of the property, the number of storeys, the length of the gutter run, and the condition of the existing fixings. As a general guide, a full replacement on a standard semi-detached house in the Aylsham area - removing old boards, supplying and fitting UPVC fascia, soffit, and uPVC guttering - would typically fall in the range of £1,200 to £2,500 depending on specification and access requirements. A detached house with a longer perimeter will cost more. Partial replacements on a single elevation are proportionally less.
Scaffolding or tower access adds to the cost on two-storey properties but is necessary for safe working and for achieving the correct board alignment. Any quote that does not mention access equipment for an upper-storey job is worth querying.
We carry out fascia, soffit, and guttering work in Aylsham and in nearby towns including North Walsham, Sheringham, and across the north Norfolk area back to our base in Cromer. If you have noticed any of the warning signs described above, call us to arrange a survey so we can tell you what you are actually dealing with before any commitment is made.
No obligation · We'll call you to arrange a free visit
Call any time. Calls are answered day and night and passed straight to our roofers.