Urgent leak or storm damage? Call 01263 808938 - answered day and nightUrgent leak? Call 01263 808938
Cromer Roofing Specialists
01263 808938 Get a Quote →

Flat Roofing in Aylsham

If your flat roof in Aylsham is showing signs of wear, catching the problem early is the difference between a straightforward repair and a full replacement.

Urgent leak or storm damage?

Call any time. Calls are answered day and night and passed straight to our roofers.

Call now: 01263 808938
Flat Roofing · Aylsham

Expert Flat Roofing
in Aylsham

What a Flat Roof Should Do - and When It Stops Doing It

A flat roof works by shedding water to one or more outlets through a slight fall built into the deck. When that system is compromised - whether through age, a bad original installation or a failed junction - water finds its way in. On garages, extensions and outbuildings, the damage can go unnoticed for months before it becomes obvious inside.

We install and repair flat roofs for homeowners in Aylsham and the surrounding area. The work covers felt systems, EPDM rubber membranes, and everything associated with getting a flat roof to perform properly for years.

The Warning Signs You Should Not Ignore

Most flat roof failures give clear signals before water actually penetrates. Learning to spot them early saves money. The warning signs worth acting on are:

  • Pooling water - if water sits on the surface for more than 48 hours after rain, the fall is inadequate or the outlet is blocked. Standing water accelerates the breakdown of any membrane.
  • Blistering or bubbling - bubbles in a felt or membrane surface mean moisture has been trapped beneath it. The pocket will eventually rupture and let water through.
  • Cracking or crazing - older mineral felt becomes brittle as the bitumen dries out. Fine surface cracks spread into splits, particularly after frost.
  • Lifted or open laps - where one sheet overlaps another, the bond can fail. A lifted lap is a direct water entry point, especially on a windy day.
  • Damp patches inside - staining on a ceiling below a flat roof does not always appear directly beneath the leak. Water travels along rafters and joists before dropping, so trace it back to the roof surface rather than assuming the leak is above the stain.
  • Deteriorating upstands or flashings - the point where the roof meets a wall is sealed by an upstand and usually a metal flashing. If the flashing is cracked, corroded or the sealant has shrunk away, this joint is the most likely entry point on an otherwise sound roof.
  • Soft or spongy decking - pressing down on the roof surface should feel firm. Any give suggests the deck beneath the membrane has absorbed moisture and is beginning to rot. This needs prompt attention because a rotten deck cannot hold fixings and will need replacing before a new membrane goes down.

Why Flat Roofs Fail - the Real Causes

Understanding what causes failure helps you ask better questions when getting work quoted. Poor installation is the most common underlying cause. A flat roof needs a consistent fall of at least 1:80 (ideally 1:40) built into the deck so water drains away. If this was not achieved at the outset, pooling becomes a permanent problem regardless of what membrane is on top.

Inadequate detailing at junctions is equally common. Wherever the flat roof meets a parapet wall, a chimney, a soil pipe or a dormer cheek, the membrane needs to be dressed up the vertical face and secured. Cutting corners at these junctions - short upstands, poorly bedded flashings, sealant used as a substitute for proper lapping - accounts for a significant proportion of all flat roof leaks.

Material degradation through age is unavoidable, but it happens sooner when the original specification was wrong for the situation. A three-layer built-up felt system on a heavily trafficked roof, or a single-ply membrane laid without the correct adhesive for an exposed location, will deteriorate faster than a properly specified alternative.

Thermal movement is another factor. Flat roofs expand and contract with temperature. A membrane that is bonded rigidly to the deck without allowance for movement will develop stress cracks at corners and perimeters over time. This is why the choice of system and how it is fixed matters as much as the material itself.

Felt, EPDM Rubber - Which System Is Right?

For most domestic flat roofs - garages, single-storey extensions, porch canopies - the two practical options are traditional torch-on felt (built-up felt) and EPDM rubber membrane.

Built-up felt uses two or three layers of bitumen-based felt, each torched or bonded to the one below, finished with a mineral capsheet. A properly installed three-layer system on a sound deck performs well and is a cost-effective solution for smaller roofs. Typical installed costs for domestic felt flat roofing run from around £70 to £100 per square metre, depending on deck condition and detailing required.

EPDM rubber is a single-ply synthetic membrane that comes in large sheets, reducing the number of joints. It stays flexible at low temperatures, which makes it less prone to cracking in cold weather. EPDM is increasingly popular on extensions where longevity and low maintenance are priorities. Installed costs typically run from around £90 to £130 per square metre for a domestic roof.

The right choice depends on the size and shape of the roof, whether the existing deck needs replacing, and your budget. A roof with multiple penetrations, pipes or awkward angles is more forgiving with felt, which can be cut and dressed into complex shapes on site. A simple rectangular roof with good falls suits EPDM well.

What a Proper Flat Roofing Job Involves

Before any membrane goes down, the deck needs to be assessed. Timber decking boards or plywood that is soft, delaminated or stained with old water ingress must be replaced - laying a new membrane over a compromised deck is a job that will fail again within a few years.

Falls should be checked and corrected where possible using tapered insulation or firring pieces. New or replacement insulation is advisable on any reroofing project, both for thermal performance and because modern building work generally expects it.

Edge trims, drip edges and outlet details should all be renewed or properly sealed when the membrane goes down. These components are far cheaper to address during the main job than to return to later.

Repairs Versus Full Replacement

Not every flat roof problem requires a full replacement. A localised repair - patching a split, rebonding a lifted lap, resealing a flashing - is appropriate when the bulk of the membrane is sound and the deck is dry and firm. A repair on a roof where the membrane is broadly degraded is false economy; the next failure will appear nearby within months.

As a general guide, if a flat roof is over 15 years old and showing multiple areas of deterioration, the cost of repeated repairs will quickly approach the cost of replacement. At that point, replacement on a sound, properly specified new deck gives a better long-term outcome.

Get a Flat Roof Survey in Aylsham

If you have noticed any of the warning signs described above, the sensible next step is to have the roof looked at properly before the next bout of rain. We work across Aylsham and the surrounding area.

Call us to arrange a flat roof survey and we will give you a clear picture of what the roof needs, whether that is a targeted repair or a full replacement with a correctly specified system.

Why choose Cromer Roofers?

  • Free survey and itemised quote
  • Fixed price - no surprises
  • Local team

Get your free quote

No obligation · We'll call you to arrange a free visit

By submitting you agree to being contacted about your enquiry. No spam, ever.

Urgent leak or storm damage?

Call any time. Calls are answered day and night and passed straight to our roofers.

Call now: 01263 808938